Craig S I killed my Traynor - debug help? -- 12/27/2003 12:06 AM
   Dai Hirokawa Hi, check out R.G. Keen's tube amp ... -- 12/27/2003 5:45 AM
   Wild Bill Hi Craig!Never fear, all is not los... -- 12/27/2003 4:11 PM
      Craig S Thanks to both of you for replying.... -- 12/27/2003 6:48 PM
         bruce Craig,You've got a problem in your ... -- 12/27/2003 9:22 PM
            Dai Hirokawa one thing I do for straight replacm... -- 12/28/2003 12:22 AM
               Craig S I took the tubes out, and those bia... -- 12/28/2003 5:02 AM
                  bruce Craig,A couple of comments on your ... -- 12/28/2003 6:02 PM
                     Craig S Hi,The arcing happened only when I ... -- 12/28/2003 6:20 PM
                        bruce Craig,What is this probe you're usi... -- 12/28/2003 6:29 PM
                           Craig S It's just a standard multimeter tha... -- 12/28/2003 6:43 PM
                              Don Symes Is it AC powered, and is it rated f... -- 12/29/2003 2:03 AM
                                 Craig S It's powered by a battery cell, but... -- 12/29/2003 5:09 AM
                                    Craig S Just about 10 minutes ago I got it ... -- 12/29/2003 6:59 PM
                                    Tom Phillips Craig,You have already measured the... -- 12/29/2003 7:10 PM
                                       Craig S I had the amp up and running, but w... -- 12/29/2003 9:58 PM
                                          Craig S I just toyed around with it a littl... -- 12/29/2003 10:11 PM
                                             Dai Hirokawa Yes (this is a circuit breaker insi... -- 12/30/2003 2:41 AM
                                                Craig S Yes, it's internal, with a red push... -- 12/30/2003 2:46 AM
                                                   Don Symes It sounds like your bias is waaaaay... -- 12/30/2003 2:56 AM
                                                      Craig S Hey everyone,Should I be worried th... -- 12/31/2003 5:41 AM
                                                         Craig S Could the fuse be at fault? It wor... -- 1/2/2004 11:23 PM
                                                            Don Symes It's possible.Remind me again - doe... -- 1/3/2004 12:35 AM
                                                               Craig S I never tried anything without the ... -- 1/3/2004 3:22 AM
                                                                  Don Symes An electrolytic cap can fail short ... -- 1/3/2004 2:57 PM
                                                                     Craig S Hey - good news.I replaced the 4 fi... -- 1/3/2004 8:18 PM
                                                                        Don Symes Lacking a schematic, I'll poin you ... -- 1/4/2004 2:24 AM
                                                                           Craig S You have been of great help. There... -- 1/4/2004 3:37 AM
                                                                              Don Symes The bias voltage is set by the R38/... -- 1/4/2004 5:16 PM
                                                                                 Craig S Thank you very much for the reply. ... -- 1/6/2004 6:48 PM
                                                                                    Craig S I put in a 50K pot and have it set ... -- 1/8/2004 2:39 AM
                                                                                       Don Symes 10 ohms seems a bit high. Check ou... -- 1/9/2004 3:58 AM
                                                                                          Craig S Hey everyoneSorry that I have been ... -- 1/21/2004 9:56 PM
                                                                                             Don Symes This isn't meant to insult your int... -- 1/22/2004 3:12 AM
                                                                                                Craig S Yes, pin 3 is indeed connected to t... -- 1/22/2004 3:56 AM
                                                                                                   Moe I hope so!!!!... -- 1/23/2004 3:09 AM
                                                                                                   Don Symes What is the DC voltage on the grids... -- 1/24/2004 12:27 AM
                                                                                                      Craig S I've got a question.... I'm pretty ... -- 1/24/2004 12:44 AM
                                                                                                         Don Symes One resistor per tube lets you chec... -- 1/24/2004 2:25 PM
                                                                                                            Craig S Thanks for the help.I removed the g... -- 1/24/2004 6:18 PM
                                                                                                               Tom Phillips Craig,Just checking. Based on the l... -- 1/24/2004 11:44 PM
                                                                                                                  Craig S Tom,I only have one 10 ohm shunt re... -- 1/24/2004 7:59 PM
                                                                                                                     Craig S I just connected Pin 3 of V5 direct... -- 1/24/2004 8:59 PM
                                                                                                                        Don Symes A datasheet is here:http://tdsl.dun... -- 1/24/2004 11:32 PM
                                                                                                                           Craig S There doesn't seem to be much diffe... -- 1/25/2004 7:42 PM
                                                                                                                              Don Symes Yes, the tube have to be in.Lower r... -- 1/25/2004 10:24 PM
                                                                                                                                 Craig S Thanks for all your help. Without ... -- 1/26/2004 12:18 AM
                                                                                                                                    Craig S Hi-Everything is still good. I had... -- 1/30/2004 10:08 PM